Page-3 news - Cangzhou Youlong Pipe Fitting Manufacturing Co., LTD

2023-08-28 Carbon Steel/Stanless Steel Cap for Pipe Connection Pipe Cap Pipe caps act as protective device and are designed to protect pipe ends of various shapes. The main purpose of using pipe caps is to waterproof the connections. They are also used to close the the ends of hydraulic or pneumatic pipes and tubes. They are used in the plumbing apparatus of domestic, commercial and industrial water supply lines, machinery and processing equipment etc. They are also fitted on water pump lines with the sole purpose of removing air blocks. Pipe caps are highly demanded as an important category of pipe fittings. Materials Used: As a large variety of materials are used for making pipe caps, the buyer should always take care of the material of the fitting before going for pipe caps. Some of the common materials used include: Aluminum Nylon or polyamide Polyethylene Polypropylene

2023-08-15 Chinese Factory ASTM ASME Pipe Fitting: Blind Flange Blind Flanges Today I will show you a kind of Steel Flange: Blind Flange. A blind flange is used to close ends of piping systems, Which is a little similar to Steel Cap. It is a kind of round plate with no center hold but with all the proper bolt holes. This blind flange is available in various sizes and materials and is used to provide positive closer on the ends of pipes, valves or equipment nozzles. This flange helps in easy access to a line once it has been sealed. The blind flange is sometimes custom made or machined to accept a nominal sized pipe to which reduction is being made. This reduction can be a threaded reduction or welded reduction. Materials used: Some materials used in the manufacturing of blind flanges are as follows: Stainless Steel Nickel Alloy Titanium Carbon Steel Cast Iron Brass Bronze Steel Aluminum Polypropylene Silicone PVC etc. Features of blind flanges: Some important featu

2023-08-02 YPCO Product Introduction:Pipe Elbow Fittings Pipe Elbow Fittings Pipe elbow fittings is a very important pipe fitting. When we talk about a pipe elbow, it means a length of pipe with a sharp bend in it. Pipe elbows are fitting accessories which are used widely in various industrial sectors in pipe fitting. A pipe elbow is frequently used in pressurized applications and are available in various shapes and sizes for use in different applications. A pipe elbow is a fitting installed between two lengths of pipe or tube allowing a change of direction, usually in the 90° or 45° direction. Materials Used for Pipe Elbow Fittings Various materials are used in the making of pipe elbows like as follows: Rubber Plastic Iron Steel Copper Stainless steel Aluminum Cast iron Ductile iron etc. Custom Made Pipe Elbows

2023-07-31 Orifice Flanges of American Standards Orifice Flanges Orifice flanges are used instead of the standard pipe flanges when orifice plate or flow nozzle is used. In other words, orifice flanges are used with orifice meters. The basic purpose for this is to measuring the flow rate of either gases or liquids in the respective pipeline. These flanges are used in various industrial applications and are available in various sizes and materials. All orifice flange units are supplied with the plate, pressure connection holes, and jack screws. Materials used: Aluminum Brass Bronze Cast iron Stainless Steel Carbon Steel Alloy Nickel Copper etc. These materials can also be used make other kinds of Flanges: Plate Flange, Slip on Flange, Blind Flange, etc. Key Features: The orifice flanges have modifications of radial tapped holes in the flange ring for meter connections. There are the orifice plate carriers in these flanges for the reason of fitting meter connections. The additional bolts available serve as a jack t

2023-07-20 Classification of elbow Pipe Fitting Classification of elbow Pipe Fitting (1) According to its radius of curvature, elbow can be divided into long radius elbow and short radius elbow. The curvature radius of the long radius elbow is equal to 1.5 times the outer diameter of the pipe, that is, R = 1.5D. The radius of curvature of the short radius elbow is equal to the outer diameter of the pipe, that is, R = D. Where D is the elbow diameter and R is the radius of curvature. (2) According to the pressure level, there are about 17 kinds of pipe standards, and the United States is the same, including: Sch5s, Sch10s, Sch10, Sch20, Sch30, Sch40s, STD, Sch40, Sch60, Sch80s, XS; Sch80, Sch100, Sch120, Sch140, Sch160, XXS, among which STD and XS are the two most commonly used. (3) According to the Angle of the elbow, there are 45 degrees elbow, 90 degrees elbow and 180 degrees elbow.